A fast drying reputation isn’t all Intercure® HS is renowned for. Complete with MIO, this primer/intermediate can improve your productivity and lower your. Allow appropriate loss factors. Airless Spray, Air Spray, Brush, Roller. PRACTICAL. INFORMATION FOR. INTERCURE Colour. Gloss Level. Volume Solids. A fast drying reputation isn’t all International Intercure HS is renowned for. Complete with MIO, this Fast cure anti-corrosive primer/intermediate with added.
|Country:||Bosnia & Herzegovina|
|Published (Last):||18 March 2004|
|PDF File Size:||7.84 Mb|
|ePub File Size:||5.25 Mb|
|Price:||Free* [*Free Regsitration Required]|
Intercure HS is not intended for use as a primer for steelwork which may be subjected to continuous immersion conditions. The figures stated above are approximate. Send us your question. Customer further agrees that we have no liability intsrcure any errors or omissions contained within the Product Data Sheets.
Over-application should be avoided as thick films will not be as good a substrate for topcoat adhesion after ageing as those at the specified thickness. GTA Do not thin more than allowed by local environmental legislation Mix ratio: Not intended for use as a primer for steelwork which may be subjected to continuous immersion conditions.
Please note that NBS product guidance is not a replacement for the manufacturer’s literature and it is recommended that International Paint Ltd be consulted before specifying.
Low molecular weight reactive additives, which will form part of the film during normal ambient cure conditions, will also effect VOC values determined using EPA Method Mouse over image to zoom. Intercure HS will normally be applied to suitably prepared steel, e.
Once the unit has been mixed, it must be used within the working pot life specified. These may be subject to variation depending on factors such as differences in color and normal manufacturing tolerances. Warning Intercure HS is preferred for use with systems for chemical environments where zinc based materials can be subject to attack in both acidic and alkaline conditions.
It is your responsibility to read the Product Data Sheets available below before you place an order intercurs prior to application of the product. If the shop primer shows extensive or widely scattered breakdown overall sweep blasting maybe necessary. Intercure HS is suitable for application to blast cleaned surfaces which were initially to the above standard but have been allowed intercuee deteriorate under good shop conditions for up to days. Absolute measured adhesion of topcoats to aged Intercure HS is less than that to fresh material, however, it is adequate for the specified end use.
Consult International Protective Coatings for further details. Frequency of cleaning will depend upon amount sprayed, temperature and elapsed time, including any delays. Once units of paint have been mixed they should not be resealed and it is advised that after prolonged stoppages work recommences with freshly mixed units.
Surface preparation All surfaces to be coated should be clean, dry and free from contamination.
However, if necessary, application over prefabrication blast primers can be performed. This product must only be thinned using recommended International GTA thinners. The minimum purchase order quantity for the product is 1.
If oxidation has occurred between blasting and application of Intercure HS the surface should be reblasted to the specified visual standard. As a primer for bs intended for use in a wide range of environmental conditions including intercurr, chemical and petrochemical plants, industrial buildings, pulp and paper mills, power plants and bridges. Press and move to zoom.
The use of alternative thinners, particularly those containing ketones, can severely inhibit the curing mechanism of the coating. Consult International Protective Coatings for further details.
INTERCURE HS – SAND (KIT / 4G) – L
Offers excellent barrier protection, low temperature cure and rapid overcoating properties. International Intercure HS Reference: This product is no longer in stock Red. Always mix a complete unit in the proportions supplied. As a primer for steelwork intended for use in a wide range of environmental conditions including offshore, chemical and petrochemical plants, industrial buildings, pulp and paper mills, power plants intercuree bridges.
Additionally, in common with all epoxies Intercure HS will chalk on exterior exposure. Varnish Hybrid Water base. The surface may deteriorate to Sa2 standard but must be free from loose powdery deposits.
Typical Coverage per coat.